6800W 4-Channel Amplifier with NomadLink Network Monitoring and Dedicated Control for Install Applications
C SERIES C 68:4
The C 68:4 Delivers 4 × 1700 W at 4 OHMS, Making This Amplifier Powerful Enough for the Vast Majority of Demanding Installed Sound Applications.
The C 68:4 delivers 4 × 1700 W at 4 ohms, making this amplifier powerful enough for the vast majority of demanding installed sound applications. Packaged in a compact 2U chassis, the C 68:4 sets a new standard for high power in an installation-dedicated amplifier.
C Series amplifiers are uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL™), which allows the output to be optimized for any loudspeaker load – whether one massive subwoofer or a series of small 100/70 V loudspeakers. VPL works in combination with adjustable input gain to achieve maximum headroom regardless of input levels or output impedances.
Every C Series is ready for the NomadLink® network right out of the box. With NomadLink, key amplifier parameters are displayed via DeviceControl software, and remote control of channel mutes and power on/off is managed efficiently under network control.
Specification
General
Number of amplifier channels |
4 |
Peak total output all channels driven |
6800 W |
Peak output voltage per channel |
141 V |
Max output current per channel |
24.5 Arms |
Max output power (all channels driven)
16 ohms |
650 W |
8 ohms |
1200 W |
4 ohms |
1700 W |
2 ohms |
1200 W |
Hi-Z per ch. (all ch.’s driven): 70 Vrms / 100 V peak |
1600 W |
Max output power bridged
16 ohms |
2400 W |
8 ohms |
3400 W |
4 ohms |
2400 W |
2 ohms |
Not recommended 1 |
Bridged per ch.: 140 Vrms / 200 V peak |
3200 W |
Performance
THD 20 Hz – 20 kHz at 1 W |
<0.1% |
THD at 1 kHz and 1 dB below clipping |
<0.05% |
Signal to Noise Ratio |
>112 dBA |
Channel separation (Crosstalk) at 1 kHz |
>70 dB |
Frequency response (1 W into 8 ohms) + 0 / -3 dB |
6.8 Hz – 34 kHz |
Input impedance |
20 kOhm |
Common Mode Rejection (CMR) |
>50 dB, 20 Hz – 20 kHz |
Output impedance @ 100 Hz |
30 mOhm |
Gain, Sensitivity and Limiters
VPL, selectable per ch 2 |
141, 118, 100, 85, 71, 59, 50, 42 V |
VPL, when bridged 2 3 |
282, 236, 200, 170, 142, 118, 100, 84 V |
Voltage Peak Limiter mode (per ch.) |
Hard / Soft |
Amplifier gain selectable (all channels) – rear-panel switches 3 |
23, 26, 29, 32, 35, 38, 41, 44 dB |
Default gain |
35 dB |
Level adjustment (per channel) |
Front-panel potentiometer, 21 position detented from -inf to |
Connectors and Buttons
Input connectors (per ch.) |
3-pin Phoenix, electronically balanced |
Output connectors (per ch.) |
Barrier strip 2-pole screw terminals |
Output bridge mode |
A+B and/or C+D, inputs A and C are input source |
NomadLink network |
On board, 2 x RJ45 connectors IN and OUT |
Intelligent fans (on/off) |
Yes, depending on presence of output signal |
Power |
Individual switches on front panel |
Cooling |
Two fans, front-rear airflow, temperature controlled speed |
Front-panel user interface
Common |
NomadLink Network; Power Average Limiter (PAL)5; Power on |
Per channel |
Signal present / High-impedance; -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL): Very High Frequency (VHF); High temperature; Fault; Mute |
Power
Operating voltage, 230 V / 115 V nominal |
130-265 V / 65 -135 V 4 |
Minimum power-up voltage, 230 V / 115 V |
171 V / 85 V |
Power Average Limiter (PAL) 5 |
Yes |
Power Factor Correction (PFC) |
No |
Soft-start / Inrush Current Draw |
Yes / max. 5 A |
Mains connector |
230 V CE: 16 A, CEE7; 115 V ETL: 20 A / NEMA 5-20P; C16:4: 15A/NEMA 5-15P |
Dimensions
Dimensions |
W: 483 mm (19”), H: 88 mm (2 U), D: 343 mm (13.5”) |
Weight
Weight |
12 kg (26.4 lbs) |
Finish
Finish |
Black painted steel chassis with gray painted steel front |
Approvals
Approvals |
CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC |